Editor's Choice
Performance
Features
Ease of Use
Value
Intended Use:
Home Theater
Epson PowerLite Pro Cinema 6030UB Projector Epson PowerLite Pro Cinema 6030UB
(add to Compare List)
Go to My Compare List

Street Price: n/a
MSRP:$3,499
3D: Full HD 3D
Contrast:600,000:1
Lumens:2400
Weight: 18.4 lbs
Resolution:1920x1080
Aspect Ratio:16:9
Technology:3 LCD
Lens:2.1x manual
Lens Shift:H + V
Lamp Life:4,000 Hrs
5,000 (eco)
Lamp Cost:$299.00
Warranty:3 year
Connectors:  Composite, Component, RGB, HDMI (x2), RS232, 12Volt Out
Video Formats:  480i, 480p, 720p, 1080i, 1080p/60, 576p

Epson PowerLite Pro Cinema 6030UB
Home Theater Projector Review

Bill Livolsi, November 15, 2013

Common Core - Epson's Home Theater Projectors

The following items are common to all three of Epson's new home theater projectors, and so represent the common core of Epson's projector technology. Unsurprisingly, these features are more or less a list of reasons why many people buy Epson home theater projectors.

Placement flexibility. Epson's projectors feature a 2.1:1 manual zoom/focus lens with horizontal and vertical lens shift, which is also manually controlled. The zoom lens can create a 120" diagonal 16:9 image from throw distances between 11'9" to 25' 1". The lens shift has a total range of 3 image heights and 2 image widths, with the middle position putting the center of the lens at the center of the screen. The range of the lens shift is roughly oval-shaped, so you cannot reach maximum horizontal and maximum vertical shift simultaneously.

Super Resolution. Epson's smart sharpening system, called Super Resolution, can increase the appearance of fine detail. The system identifies blurred portions of the source image and selectively applies sharpening to these areas, then compares the sharpened image to the original and attempts to minimize the differences in order to reduce artifacts. Super Resolution shows improvement compared to last year's implementation, leading to an increased perception of detail with fewer artifacts overall. When taken too far, it can still cause mild ringing or artificiality, but a setting of 2 or 3 (out of 5) is effective while still being subtle.

Full HD 3D. Epson's 3D system is as hassle-free as it gets. The system uses radio-frequency glasses synchronization to eliminate interference with remote control signals. The projectors have multiple dedicated 3D viewing presets which can be calibrated independently, allowing you to save more than one calibration for 3D viewing. This makes it easy to have a bright setting for television and animation and a more subtle, reserved setting for film.

The 3D Glasses (model ELP-GS03) are lightweight and comfortable, and their batteries are rechargeable over USB (a cable is included with each pair). Each projector comes with two pairs of 3D glasses, and additional eyewear costs $99 from Epson.

3D brightness can be adjusted to one of three levels, which allows the user to trade between image brightness and crosstalk elimination based on the content being viewed. The default setting is Medium, which allows 25% total light transmission. Medium brightness effectively eliminates crosstalk in all but the most difficult content, and was our preferred setting throughout testing. Low brightness, at 18.5% light transmission, removes any trace of crosstalk whatsoever, but also restricts screen size due to less light making it to your eyes. High brightness, at 29.5% transmission, is great for 3D content where crosstalk is less of a concern. While we did not switch away from Medium very often, we appreciated having the option available for those times when the content demanded a different approach.

B&W Cinema. Black and white movies look their best at around 5500K color temperature, which is close to the color temperature of the commercial projection systems in use back in the 1940's and 50's. When you try to watch them in a mode that has been optimized for color films, they end up looking cold and uninteresting. The Epson 4030, 5030UB, and 6030UB all include the "B&W Cinema" image preset which is intended to display classic black and white films as they were originally seen in theaters. It's a big help when you're a fan of the classics but don't want to adjust your Cinema calibration every time you watch a black and white film.

Picture in Picture. As the name implies, Picture in Picture (PIP) displays a small secondary image from a separate source in a corner of the larger main image. Epson's home theater projectors have had PIP capability for years, but this year the system is able to use HDMI inputs for both images. This is a big deal -- in the past, projectors typically had one set of HDMI circuitry, and could not use digital sources for both inputs. The use of two digital sources for PIP is a first for Epson home theater projectors and may in fact be unique in the market today.

Lamp. All three projectors use the same 230-watt E-TORL lamp, which is rated for 4,000 hours of use at full power and 5,000 hours in Eco-mode. Replacement lamps cost $299 each.

Low to moderate fan noise. Perhaps due to the use of a relatively low-wattage lamp in a large chassis, none of Epson's new home theater models creates much audible noise in eco-mode. Eco-mode is nearly silent, and sitting any farther than a foot away from the projector means you won't hear it running. In full lamp power mode the fan noise can be noticeable during quiet interludes in a film, but it is low in pitch and not overly distracting.

Warranty. Each projector has, at minimum, a two-year warranty which includes 90 days of lamp coverage. The Pro Cinema 6030 and 4030 extend this warranty to three years. Up to two years of additional warranty coverage is available for purchase on the 5030, if desired.

Automatic iris. Epson has perfected the automatic iris by creating a system that is both effective and unobtrusive. The iris deepens black levels in scenes with low illumination. It has two settings, Normal and High Speed, with High Speed being the more aggressive of the two -- the iris in High Speed appears to react more quickly than in Normal mode.

Connectivity. All three projectors have two HDMI ports, 3-RCA component input, a 12V trigger, and an RS-232C port for external command and control. The Home Cinema 5030 has a wireless model, the 5030UBe, which also include a WirelessHD transmitter with 5 additional HDMI inputs and MHL compatibility.

Calibration and customization. The menu system gives the user total control over color, contrast, and gamma. Each projector features full RGB Gain/Bias controls for grayscale adjustment as well as a full color management system for fine-tuning gamut. Each projector also has at least some amount of control over gamma. Ten user memory locations allow you to save different calibrations for the same image mode without overwriting your previous settings, and these memory slots can be renamed as well.

Panel alignment. The panel alignment system can correct for convergence errors, which are almost an inevitability in a three-chip light engine. As the projector is used and components age, there may be some tiny shifts in the positioning of the LCD panels used to create the image. Using the panel alignment system, you can correct for these shifts without sending the projector out for service, thereby reducing downtime and expense.

Key Features of the Epson 6030UB

2D picture quality. The best reason to purchase the 6030UB, hands down, is image quality. The 2D picture from the 6030UB is high in contrast, impressively three-dimensional, and after calibration has spot-on accurate color. Thanks to an aggressive and effective automatic iris, the 6030UB offers the best black level performance found in any projector in its price range, period. Detail is sharp and clear even without the use of Super Resolution, though that technology can make detail pop even more than it already does. Frame interpolation is very effective at reducing judder in 24p material, and shows few artifacts.

3D picture quality. If you care about 3D theater, the 6030UB delivers a compelling experience. The 3D image from the 6030UB has no noticeable flicker, almost zero crosstalk, and is bright enough to display on large screens. That last point is crucial; insufficient brightness is a major cause of headaches and eye strain when watching 3D movies and video. The 6030UB's 3D Dynamic mode is bright enough to power a 100" diagonal 1.3 gain screen at over 16 fL. That measurement was obtained using the Low 3D brightness setting and already accounts for light loss from the 3D glasses. Using those same settings, the Medium brightness setting is just about bright enough for a 120" diagonal screen. To top things off, Frame Interpolation is available in all 3D image modes.

The "Pro Cinema" package. The Pro Cinema 6030UB includes a number of extras not included with the Home Cinema 5030UB, which we've taken to calling the "Pro Cinema" package. These include a Chief ceiling mount, a spare lamp, a cable cover, and a three-year warranty instead of the standard two. As a result, the 6030UB has an MSRP of $3,499 versus the $2,599 of the 5030UB.

As it happens, Epson does sell all of those accessories separately. If you were to purchase an Epson 5030UB ($2,599) and then add a spare lamp ($299), Chief RPA Elite ceiling mount kit ($296.99), cable cover ($50), and an additional one year repair/exchange extended service plan ($279.99), you'd end up spending $3,524.98. Compare this to the $3,499 price of the 6030UB, and then remember that you still wouldn't have anamorphic lens compatibility without an outboard image processor. The 6030UB costs more, but that doesn't mean it lacks value.

While this isn't quantifiable, there is one additional benefit to purchasing the 6030UB. Since the projector is sold through custom installation professionals and specialized dealers rather than Internet vendors, you get the benefit of a local point of contact in the event that something goes wrong or you have a question about the product that isn't answered in the manual. In other words, you get customer service from a real person you've met before.

Anamorphic Widescreen. As the only current Epson home theater projector capable of anamorphic stretch, the 6030UB has special appeal for those interested in ultra-wide 2.39:1 anamorphic cinema. In addition to the obvious lens compatibility, the 6030UB also has a 12V trigger which can be used to actuate a motorized sled and move your lens out of the light path when watching non-anamorphic content. The projector's lens is centered in the case, which can make installation easier -- and easy installation becomes doubly important when an anamorphic lens is involved due to the increased complexity of the system. The projector's long zoom and H/V lens shift can likewise make mounting easier. You can even use the projector's panel alignment system to correct for any chromatic aberration caused by the anamorphic lens, should you wish to do so. All in all, the 6030UB is a projector designed to take an anamorphic lens and make that addition as simple as possible for the user.

Frame interpolation. Frame Interpolation is a technology that reduces the appearance of judder and motion blur by adding interstitial frames to a source video signal. Frame Interpolation has three settings as well as an Off switch (it starts out disabled). Low, the most conservative setting, does not eliminate judder but also has the least noticeable digital video effect. Normal, the next setting, drastically reduces judder but can increase the appearance of DVE in some content. We found the appearance of digital video effect to be highly content-specific. Some films show DVE on Low, while others do not show much DVE even with Frame Interpolation set to High. Low is a safe all-purpose setting for reducing judder in most film and video, though, so we left FI set to Low for the majority of our testing.

ISF Certified. The Pro Cinema 6030UB is almost physically identical to the Home Cinema 5030UB, but it does carry ISF certification where the 5030UB does not. ISF Certification guarantees that the projector's controls are independent, meaning they do not affect one another -- so when you adjust white balance, for example, you will not see a shift in brightness or color saturation. The projector does not include any additional menu options or image controls as a result of this certification.

Previous Page
Setup and Configuration
Next Page
Performance
Review Contents: The Viewing Experience Setup and Configuration Key Features Performance
  Limitations Conclusion

Reader Comments(15 comments)

Posted Sep 5, 2014 8:39:07 PM

By Aussie Bob II

Post a Comment Alert Moderator
Re. your comments on anamorphic lenses.

Only prism-based lenses ike the Cinevista have fixed focus. Cylindrical lenses are all focusable.

Secondly, color aberration is non-existent in a good cylindrical lens. The Cinevista is, as you say, the entry level lens from Panamorph. It has no color aberration correction.

A good cylindrical lens like a Xeit (which my company makes) or a Schneider have none of the color, focus or sharpness problems you mentioned as being part of the CineVista "experience".

Posted Jul 21, 2014 12:22:03 PM

By dave

Post a Comment Alert Moderator
can I make the 6030 ub wireless hdmi? aftermarket?

Posted Jul 15, 2014 5:47:01 PM

By Steve

Post a Comment Alert Moderator
I am considering using the Epson 6030UB with a 108" Black Diamond Zero Edge screen with a 0.8 gain. The projector will be placed in the ceiling about 19 to 20 feet from the screen in a media room without any light. Is this a good combination? Thank you for your assistance.

Posted Apr 7, 2014 12:38:40 AM

By Iftikhar Awan

Post a Comment Alert Moderator
Why not a projector with a built-in anamorphic lens? I mean a separate model for 2.39:1 aspect ratio movies.

Posted Feb 8, 2014 8:27:25 AM

By Mike

Post a Comment Alert Moderator
Will this projector do 1080P/24?

I don't see it anywhere in its specs.

Thanks.

Posted Jan 23, 2014 12:47:02 AM

By Greg

Post a Comment Alert Moderator
What are the mounting requirements for the Epson 6030? Is it top of screen and center, or is it recommended to be mounted bellow the top of the screen? I know we can always keystone a projector and lens shift. But it's my understanding for the best image we should mount the projector correctly. And when done so we won't need to using the keystone and lens shift etc. Looking at their site, I get the impression that the projector should be mounted about 1/4 the way down bellow top of the screen. To me that's a little disappointing. I'd like to have it ceiling mounted, and yet still work well with a 2.39:1 lens. But worry it won't work it's best without pincushioning etc if the protected isn't mounted in the best position. Which means it's pretty low compared to the audience. Was this your finding with your testing?

Thanks for any feedback

Greg

Posted Dec 11, 2013 7:03:39 PM

By Munster

Post a Comment Alert Moderator
Bill, I have a question regarding the saving of different RGB settings for each color mode. As you state, changing the RGB for one Color Modem, changes all of them. How do you save it to emory? I have tried and it still replaces whatever was there with the latest adjustment. Thanks

Posted Nov 26, 2013 4:43:27 PM

By Ryan

Post a Comment Alert Moderator
I saw a projector calculator for this projector and it said the throw distance could go up to 23' back w/ a 110" 16.9 screen. Will I still get a great picture if I mount it in the back of my room at 22 feet? I've heard yes but I might lose brightness but could gain crispness in picture quality. I just want to make sure it's OK to mount it that far back w/out losing quality?

Also if I did have a 2.35 screen will the anamorphic mode on this new projector allow HDTV/Sports to show in full screen mode on a 2.35 screen? If it does, will it still be a great picture or do you lose quality when it's expanded? Thanks

Posted Nov 21, 2013 2:24:27 PM

By Zee

Post a Comment Alert Moderator
One interesting thing about the anamorphic lens with a slide - if the more expensive lens and slide mechanism costs more than a projector and a fixed lens, why not simply mount two projectors - one with a fixed lens for 2.35, and one without a lens for 16/9?

Posted Nov 20, 2013 5:49:59 PM

By Romel

Post a Comment Alert Moderator
Bill,

Thanks for providing some clarity on this subject; It's very much appreciated. Its nice to know that we have sites like PC that can set the record straight.

Posted Nov 20, 2013 7:59:41 AM

By Sanjay Shanbhag

Post a Comment Alert Moderator
How does this compare, in your opinion, to the: DLA-RS4810U

with respect to black levels, colour quality, etc.

We were suggested to the JVC...we've tested it with our ps3 and we didn't notice lag on it. movies looked good. Black levels seemed nice. Our room when we get a projector isn't very dark. At night, it gets dark but the walls are lightly coloured.

Thoughts?

Regards,

Sanjay

Posted Nov 18, 2013 12:02:10 PM

By Bill Livolsi

Post a Comment Alert Moderator
Patrick - Yes, the Epson 6030UB is much better than the Mitsubishi HC3200. You will see a large difference in picture quality.

Romel - That's what I thought, as well, but the folks at Epson say that's not the case.

From a user standpoint, the menu systems of the 5030UB and 6030UB are identical, so any such controls would be in a service menu or passcode-protected and only accessible to ISF certified technicians. That's not terribly unusual in projectors, so I asked for instructions on how to access the ISF menu and I was informed that there isn't one. There are no additional calibration control systems on the 6030UB.

Tony - You're right, I misspoke. I made the same mistake in the 5030UB review and I've now corrected both. Thanks for the heads-up.

The loss of clarity is intentional; Epson is aware of it and does not consider it a flaw in the projector. I'm not sure from your question what you want me to contact Panasonic about, so I suspect the Typo Bug bit you, too. ;)

Posted Nov 18, 2013 7:51:15 AM

By Tony

Post a Comment Alert Moderator
I think this is a mistake: "The end result is that the 6030UB is faster in "Fine" mode but slower in other modes than the 5020UB was last year. Since gamers who care about input lag are unlikely to use anything but the fastest setting available, this comes out as a win for the new model. "

According to your results, the 6030IB is faster in "FAST" mode but slower in "FINE" mode than the 5020UB.

The only think holding me back from this projector is the reduced clarity in fast mode (yes it matters to me even if it's only noticeable on text in games). Is there any way you guys can contact Panasonic and see if there will be a fix for this issue? Thanks

Posted Nov 18, 2013 7:10:22 AM

By Romel

Post a Comment Alert Moderator
Bill, Evan,

I was informed that the Epson 6030 has ISF calibration settings that the 5030 does not have, which allows the 6030 to be calibrated in a way to produce a better picture than the 5030.

My question is does the ISF setting used by authorized calibration technicians allow the 6030 to produce a better picture than the 5030 or does these settings allow the 6030 to simply be calibrate quicker and more easily? I have yet read anything stating the 6030 can produce achieve a better calibrated picture than the 5030. I think I asked this question before but don't remember gettng an answer. Thanks in advance for providing info on this subject.

Posted Nov 17, 2013 9:31:54 AM

By patrick

Post a Comment Alert Moderator
hello j'ai actuellement un Mitsubishi hc 3200 dans un salon non dédié. Ecran de Projection 16/9 Lumene Embassy II 240C 132 x 234 cm.j'utilise PS3/4 +pc gamer hd 60% je regarde quelques blu-ray 30% l'Epson 6030UB est-il nettement meilleur? cordialement

patrick ....................................................... Hello: I have at present Mitsubishi hc 3200 in a not dedicated lounge(show). Projection screen 16/9 Lumene Embassy II 240C 132 x 234 cm.j' uses PS3 / 4 pc gamer hd 60 % I look some at Blu-ray 30 % Epson 6030UB is it clearly better? Cordially

Patrick

Post a comment

Commenting on this article is easy and does not require any registration. Your email address is necessary for you to activate your comment once it has been submitted. It will not be shown to other site viewers. ProjectorCentral reserves the right to remove any comment at any time for any reason. Foul language is not permitted, nor are personal attacks. All comments should remain on topic.

Name:

Email Address:(used only to confirm your comment)

Your Comment:

(Enter the numbers as they appear to the left)